Auto is pretty much the same as high. The Unifi AP will show up in the list of discovered devices. He left no instructions.Spectrum has installed a new modem and router. What you also will discover is that they are super easy to setup and manage.
). Select the devices that you want to configure. If you left everything on default then the transmit power is set on auto for each access point. I just connected my NanoHD and all is well, except..My main router is in my office in the far reaches of my house.
And if you like statics, you will get some great insights into your network as well.Ubiquiti offers a wide range of Access Points, but in this article, I will focus on the most used access points for home networks and small-medium sized businesses. And if so How would that work? Reading is fundamentalRudy, I have been searching for a long while for a site that makes setting up an area network for home use and yours has proved to be the best for simple easy to follow instructions. To manage our access points we are going to install the Unifi Controller. Unifi Acces Points are based placed on the ceiling, instead of mounted to a wall. The Aps have being reset to factory values, but the system doesn´t recongnize them.I’ve set up three APs with one SSID + Guest, all three APs are one different channels 1, 6 and 11.You shouldn’t have to worry about the channels, just leave in on auto and the Unifi controller will work it out.
You can run them through a netgear switch, that won’t be a problem, as long as they can get power (with the PoE adapter or with the netgear switch)i have a adoption problem..control status shows like adoption failedI have disbaled my antivirus and firewall but still can not find deviceDo you get a blank page, or can’t you find the access point at all?I have a problem discovering the APs, I mean I connect them properly to the PoE switch, and the configuration on the switch is also the rigth one to reach the Controller.
UniFi® AP HD.
The UAP-AC-IW are connected to a PoE switch in our office which is connected to the SonicWall router (as are all other hardwired devices on our network).Do the wireless clients get the same Ip range as the wired clients?
They continue to develop new features for their software, making it easier for you to manage your WiFi network.
Open the controller and for each device, go to settings > open radios and set the transmit power to low.
You will have to check the signal strength, if you set it to high (or on auto) the change is that mobile devices will stay connected to indoor AC while the outdoor can give you a better performance.Hi Rudy, thanks to both your guides I now have installed both an ERX router and a Unify AP AC LR.
What ended up working for me was creating a second wireless network where i set the ‘Combine Name/SSID’ field to off, so there was a different ssid for the 2.4 and 5ghz networks.
so back to Auto channel configuration, but no improvement.I wonder what I did wrong.
You can adopt new UniFi devices during the initial controller setup or do it later.For an in-depth guide for adopting UniFi devices, see If you need to replace your current router with a USG, see The UniFi devices can have two possible factory-default credential sets:Note that you may require multiple sets of credentials when using UniFi:To use the 'Forgot Password' option, you will need to configure your SMTP credentials first.For a guide on using Gmail SMTP to reset the password, see Since UniFi devices retain their settings, internet connectivity will work even if the controller is offline.However, the features running directly on the controller will be lost. I tried to put all AP’s on different channels, but that only seems worse. I'd like to reconfigure the controller with the same SSID's, passwords, and VLANS. The iphone was able to connect to that.We have two UAP-AC-LR indoor and looking for the best option to extend outdoors (to ensure coverage on the terrasse) the wireless network. One labelled “LAN” that goes to your router and another labelled “POE” that goes to your AP.Thanks for this tutorial. You will have to check the signal strength, if you set it to high (or on auto) the change is that mobile devices will stay connected to indoor AC while the outdoor can give you a better performance.Hi Rudy, thanks to both your guides I now have installed both an ERX router and a Unify AP AC LR.