how to access dsl modem in bridge mode

How to get into a modem/router that is in bridge mode Join the conversation!Enter another ZIP to see info from a different area. I know every single method to get into a device while it is in bridge mode. The modem has to be bridged before connecting to a router since applications like VPN, P2P, and remote management require a public IP Address on the router WAN port for a successful connection. Help others. You will need to adjust as need be.a) the device that is in bridge mode LAN IP 192.168.1.1 with the subnet mask of 255.255.255.0b) Primary NAT router's  LAN IP 192.168.2.1 with the subnet mask of 255.255.255.0#3 A wired NIC gets disconnected from the Primary NAT router.#4 Setup a Local Static IP for that NIC that is connected to one of the other LAN ports of the the device that is in bridge mode.#6 Again, do not set a Default Gateway or edit the DNS Settings on your computer.#7 The Wired NIC that you disconnected gets connected to one of the other LAN ports of the device that is in bridge mode.#9 But this time since you have two NICs, it is possible to access both routers - access the Internet at the same time. … Quick Way to Configure DSL Modem in Bridge Mode. If you need help, here is Copyright © Home-Network-Help.com All rights reserved. If you plan to connect the modem to router and set up a home network, you must set bridge mode on modem too. If you need help, here is Copyright © Home-Network-Help.com All rights reserved. This requires that you have both routers (Dual WAN one and the one that you want to get access to) in different subnets and I believe that the other connection should also be in a different subnet from those two devices.Like for example the cable modem LAN at 192.168.100.1, the device that you want to access with only LAN port LAM at 192.168.1.1 and the DUAL WAN port router LAN at 192.168.2.1Q: But what if my router that is in bridge mode that I want to get access to has only one LAN Port and I have more than public IP from Verizon with this DSL/Fiber Connection?Answer: I sort of gave this answer already.

DSL Modem: Used in bridge mode + NAT/DHCP/Firewall turned off. Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type. 5) Go to the correct configuration page by referring to modem manual, and then set the operation mode to Bridge mode. 1) Connect DSL modem’s LAN port to computer’s network card by using straight through network cable. If you do not have one already, I recommend a networking switch with Auto MDI-X so that you do not have to worry about the type of networking ethernet cable.Step 2: Disconnect the device you want to get into is in bridge mode that has only one LAN port from your primary NAT router.Step 3: Connect one wire to the device you want to get into is in bridge mode that has only one LAN port to the networking hub/switch.Step 4: Connect one wire to your primary NAT router to the networking hub/switch.Step 5: Power up the networking hub/switch that is between the the device you want to get into is in bridge mode that has only one LAN port from your primary NAT router.Step 6: You are to connect your computer to the networking hub/switch that is connected between the device you want to get into is in bridge mode that has only one LAN port and your primary NAT router.#1 Your computer must have two NICs, one of the NICs must be a wired NIC., you must know how to setup a manual Static IP on your computer (see option one above, I have a link to a place that provides directions), and both routers can not be in the same subnet.#2 Here is an example of what I mean by two subnets. This article briefly explains how to configure DSL modem in This is very common setup after you have subscribed new DSL broadband service, you just need to configure the modem as a bridge, and after that configure PPPoE dialer in Microsoft Windows by providing username/password or other network information for accessing Internet. ** Option #1 ** #1 Your computer must have a wired NIC. Here is an example: 7) Ok, at this stage you have done the modem configuration, you can then proceed to configure PPPoE dialer on connected computer. )#2 Setup a Static WAN IP of the RJ-45 router so that is in the same subnet as the device that is in bridge mode.#3 Based upon what you are trying to do, assuming the same subnets setting before you must use:#5 Be strongly advised as long as the RJ-45 router's WAN IP is set to Static and is in the same subnet as the the device that that in bridge mode and if the Primary NAT router is not a Dual WAN port router of any kind (RJ-45 WAN1 and RJ-45 WAN2, RJ-45 WAN and 4G/LTE, RJ-45 WAN and POTS dial-up, ETC..) you (and the computers that are behind this RJ-45 WAN port router) are not going to be able to access the Internet! 5) Go to the correct configuration page by referring to modem manual, and then set the operation mode to Bridge mode.